Solar & Battery Storage kit, with 3.8kW of solar panels + up to 10.5kWh of battery Storage + 5 KVa Victron Inverter/Charger + Online monitoring. Works in a Power Cut
Solar and battery storage kit
This is a Victron home battery storage and solar kit that can be used as the primary source of renewable power for your property.
You could also add it as a battery storage system to an existing solar installation, with the added benefit of some more solar power that can also charge your battery from the solar panels that are included in the kit.
How to install
The installation of this kit is relatively straight forward requiring solar panels to be placed on the roof or on the ground, with DC cables brought back to the inverter charger and connected to the internal MPPT. it would then be required to wire this into your electrical consumer unit and the blue CT and cable to be run to your incoming supply to monitor what you're drawing from the grid. the batteries need to be placed next to or underneath the inverter and a cable and isolator run to the bottom of the inverter charger. once this is done you are ready to produce renewable electricity
How it works with an existing Solar system
When this Victron home battery storage system is set up to work with an existing solar installation, you would wire it into the mains and connect the blue CT clamp around the incoming supply. This CT detects the flow of power in and out of your property when there is excess solar the CT will detect this and allow the battery to charge. However, when there is no solar or little solar and power from the grid passes by the CT this will tell the battery to discharge and cover the load that the grid was supplying, this means that your bill will be reduced and your purchasing of electricity from the grid will be less
How this battery works with cheap rate electricity
If you don't have solar or even if you do have solar you can charge your battery from cheap overnight electricity using a smart meter or Economy7. This means that while you're asleep your battery system can come on automatically and charge from this cheap rate electricity and again turn off automatically, this is normally between 4 & 6 am. This would enable you to run your house on batteries for the remainder of the day depending on your usage.
Power during a power cut or blackout
Built into the Victron inverter charger is a secondary output which can be used in the event of a power cut to provide power from the batteries to keep your house powered with electricity to run things such as fridges freezers boilers and lights
Built into the Victron is a GX device, this GX device will plug into your Internet connection or connect to Wi-Fi and allow you to monitor and control your system from anywhere in the world. This GX device is controllable from your mobile phone or laptop and allows you to make settings changes and to enable and disable charging schedules. It would also allow Callidus to come onto the system remotely and check that it's working correctly once you have set it up.
If you are installing this alongside an existing solar system, then you may wish to see what is being produced by that existing solar system on the Victron monitoring. This will require the purchase of an ET112 meter and RS485 to USB cable, this will allow you to see what's being produced by the existing solar system, however, it isn’t necessary for the system to work as the CT provided will capture all energy as it tries to exit or enter the building. the links below are for these two products
This kit is a 48V 5000 VA system with a choice of AGM battery storage
The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16-character display.
These elements come prewired together inside a single unit. This greatly simplifies most installations, saving time and money.
Grid in-line topology
The EasySolar-II GX will use excess PV power to charge the batteries or to feed power back into the grid and will discharge the battery or use power from the grid to supplement a shortage of PV power. In case of a power outage, the EasySolar-II GX will disconnect the grid and continue to supply the loads. Loads that should shut down when AC input power is not available can be connected to a second output (not shown). These loads will be taken into account by the PowerControl and PowerAssist function in order to limit AC input current to a safe value.
Grid parallel topology
The EasySolar-II GX will use data from the external AC current sensor (must be ordered separately) or power meter to optimise self-consumption and, if required, to prevent grid feed. In case of a power outage, the EasySolar-II GX will continue to supply the critical loads
Display and Wi-Fi
The display reads battery, inverter and solar charge controller parameters. The same parameters can be accessed with a smartphone or other Wi-Fi enabled device. In addition, Wi-Fi can be used to set up the system and to change settings.
Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the MultiPlus-II inverter/charger. The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.
The integrated GX device includes:
• A BMS-Can interface. This can be used to connect to a compatible CAN-bus managed battery. Note that this not a VE.Can compatible port.
• A USB port
• An Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a VE.Bus and a VE.Direct connection.
PLEASE NOTE UPON PURCHASE A MEMBER OF THE TEAM WILL BE IN TOUCH TO DETRMINE THE CORRECT ROOF EQUIPMENT FOR YOUR ROOF
All of our useful downloads can be found here
Whats in the Kit
- EasySolar-II GX 48/5000/70-50 (PMP482507010)
- 10 x 400W Solar Panels
- Solar isolator
- Battery isolator
- 50 metres solar cable
- 5 pairs of MC4's
- 3 x 350mm of 70mm2 battery link cable (for 5.2kWh system) or 8 x 350mm of 70mm2 battery link cable (for 10.5kWh system)
- 2 metres of 70mm2 cable red
- 2 metres of 70mm2 cable black
- Mega fuse holder
- 200A mega fuse
- BMV 712 Battery monitor
- Assortment of lugs
- Roof rails and mounts
- Current transformer
- A choice of battery storage:
- 4 x 110ah AGM batteries (5.2kWh) or 8 x 110ah AGM batteries (10.5 kWh)
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.